How to Insert SD Card Into NamelessRC Naked GoPro

The NamelessRC Naked GoPro is super lightweight, compact, and ideal for FPV drones. It’s basically a stripped-down version of a regular GoPro, designed for aerial footage without the extra grams. But with all that minimalism, figuring out how to insert an SD card can feel a little mysterious.

TL;DR

To insert your SD card into your NamelessRC Naked GoPro, first locate the MicroSD slot on the mainboard. Make sure the camera is powered off and orient the card correctly. Gently slide it in until it clicks. It’s that simple! Now you’re ready to capture awesome flying footage.

What You’ll Need

• Your NamelessRC Naked GoPro (of course!)
• A compatible MicroSD card (Class 10 or UHS-I recommended)
• A set of steady hands
• Optional: tweezers, flashlight

Step 1: Power Off the Camera

Before doing anything, make sure the camera is completely powered off. Unlike the regular GoPro, the naked version often has custom wiring and might be connected to a flight controller.

Unplug it or cut its power source. It’s good practice, and it helps avoid glitches or card corruption.

Step 2: Find the SD Card Slot

Here’s where the fun begins. If this is your first time, be ready for some tiny tech adventuring. The MicroSD card slot is not on the outer frame like regular GoPros.

Instead, it’s on the mainboard. Where exactly depends on how the camera has been stripped down and which version of the board you have.

It’s usually on the back of the camera or near the side, next to the USB connector or battery input. Use a flashlight to inspect the board if it’s not immediately clear.

Step 3: Check Card Orientation

Handling cards the right way saves you from damaging the slot. The MicroSD card should be facing label side up (that’s the side with logos).

Be gentle. If you’re forcing it in, something’s wrong. Pull it out and try again. Some versions may have a slot where the card goes label down, depending on camera orientation—so check it closely.

You’ll hear or feel a slight “click” when the card’s in all the way. There’s no latch or cover—just a flush fit.

Step 4: Test the Fit

Wiggle it a tiny bit to ensure the card doesn’t fall out. Don’t shake it; just a tiny tap test.

If it feels loose, eject it gently and reinsert. Make sure it’s not half-in or misaligned. Naked GoPros are compact and don’t give you much margin for error.

Optional: If your build is enclosed inside a frame, test clearances so removing the SD card later isn’t a hassle. Some FPV frames make it tricky to access slots!

Step 5: Power On and Check Recording

Power it back up! If your setup has an FPV display, you’ll see the recording interface showing how much space is on the card.

Do a quick test recording to make sure everything is working fine. Check that the footage saves correctly and plays back as expected.

SD Card Tips for Best Results

• Use fast cards: Go for Class 10 or UHS-I (V30 or higher is gold). Slow cards = missed frames!
• Capacity matters: 32GB to 128GB is usually sweet. Bigger cards may not always be compatible.
• Format regularly: Format in-camera or on a PC with FAT32 or exFAT to keep things clean.

Common Mistakes to Avoid

• Inserting the card while powered on: This can corrupt both the card and the firmware.
• Forcing the card: Don’t jam it. If it doesn’t go in smoothly, reverse it or realign it.
• Using poor quality cards: Cheap cards might fail mid-flight, and that means no footage!

Bonus Tip: Use Tweezers or a Card Tool

If your fingers are too big or your build is tight, use tweezers or a plastic card-pusher. Just don’t use metal tools while your gear is powered—it could short something!

How Do I Know It’s Working?

• The GoPro menu will show storage info.
• You can record and view a clip.
• The SD card shows up on your computer with saved files.

Still Can’t Find the Slot?

If your camera is embedded into your drone build and still has no visible SD slot, there’s a chance:

• You’re missing a module cover that hides the slot.
• Your build is super compact and needs disassembly to access the card.

Check your specific build layout or look up a disassembly guide for your model of NamelessRC Naked GoPro.

Final Words

Inserting an SD card into a NamelessRC Naked GoPro might look tricky, but it’s very doable once you find the slot. Take your time, be gentle, and double-check the card’s orientation.

Once it’s in, you’re all set to fly and film like a boss!

Fly safe, shoot sharp, and never forget to hit record!